Aqua-Seal Chemical MSDS

18 / 54

DESCRIPTION
Aqua-Seal Gold+™ utilises the latest Rapid-Seal STC™
Technology to provide stain resstance in 4 hours. Aqua
Seal Gold+ is a below surface sealer formulated to provide
maximum stain resistance & keep a natural look on porous
unsealed surfaces. Aqua-Seal Gold+™ is water based, non
flammable, non toxic, & LOW VOC (40 grams/litre). Can also
be used as a pre-grouting sealer. Allows excellent Moisture
Vapour Transmission (MVT) For interior and exterior use.
USES
Use on all natural stone, grout, porous ceramic & porcelain,
terracotta, Saltillo, quarry tiles, terrazzo, concrete, pavers &
masonry surfaces where a natural look and maximum stain
resistance is desired.
TEST FIRST
Due to the nature of different surfaces, you should do several
tests in inconspicuous areas according to the label instructions
to determine application method, number of coats & desired
results. The end user must determine the suitability of the
product for their intended use.
PRE-GROUT SEALING
This will allow quick & easy cleanup after grouting as grout may
stain surfaces. Do not to saturate the open grout joints. Follow
application instructions below.
PRECAUTIONS
1. Always Test first;
2. Read entire label & product technical bulletin before using;
3. Wear appropriate skin and eye protection & use in a well
ventilated area;
4. Surface must be clean & completely dry and free from any
other sealers & coatings;
5. Use when surface temperature is between 4°C & 32°C.
INSTRUCTIONS
1. Shake well before using;
2. Sweep, vacuum, or wipe surface;
3. Apply product using an Aqua-Seal Sealer Sponge, sealer
applicator, paint pad or cotton towels;
4. After 5-10 minutes, remove any sealer visible on the surface
by wiping the surface COMPLETELY DRY with absorbent
paper or cotton towels. DO NOT ALLOW THE PRODUCT
TO DRY ON THE SURFACE;
5. If 2 or more coats are required, allow minimum 30 minutes
between coats and follow label instructions for each coat;
6. The surface is ready for light traffic after 2 hours. Keep
surface dry for 12 hours.
Note: 2 hours after the final coat, conduct a test to determine if
the surface is properly sealed by applying a few water droplets
to the surface. If the water is easily absorbed then apply an
additional coat. Wait 2 hours and repeat the test.
LIMITATIONS:
• Do not allow the product to come in contact with any non-
recommended surfaces;
• Sealer will not prevent surface wear or etching from harsh
chemicals;
EXPECTEDWEAR
Up to 20 years but will vary depending on texture and
hardness of surface, surface wear plus frequency, and type of
maintenance products used. Harsh cleaning methods, and
high-alkaline, acidic, or solvent-based cleaners and weather
exposure will affect wear and performance. Re-seal as
necessary.
COVERAGE
Approximately 40-160m 2 per 4 litres per coat. The coverage will
vary depending on density, porosity, texture, surface absorption,
weather conditions, the application method and number of
coats. As a guide: Porcelain Tile – 160m2, Polished Granite 160m2,
Sandstone 40-60m2, Honed Travertine 75-110m2.
For full coverage chart refer to
MAINTENANCE:
• Aqua-Seal EzyClean™ for routine, everyday cleaning;
• Aqua-Seal XtremeClean™ for periodic heavy duty cleaning;
• Aqua-Seal DeepClean Pro™ for large commercial areas.
HANDLING AND STORAGE:
• Close container tightly after each use.
Store in original container only.
• Store in temperatures between 4°C and 32°C.
FIRST AID
For advice, contact a Poisons Information Centre (Phone
131 126) or a doctor. If swallowed, do NOT induce vomiting.
Immediately give at least 3-4 glasses of water. If in eyes, hold
eyelids apart and flush the eye continuously with running
water. Continue flushing until advised to stop by the Poisons
Information centre or a Doctor, or for at least 15 minutes. If
skin or hair contact occurs, remove contaminated clothing
and flush skin and hair with running water. If irritation persists,
seek medical attention. If inhaled, remove to fresh air. If not
breathing, give artificial respiration. If breathing is difficult, give
oxygen. In case of accident or if you feel unwell, seek medical
advice immediately
SAFETY DIRECTIONS
Avoid contact with skin and eyes.SAFETY DIRECTIONS
WARRANTY
Aqua-Seal STC™ “The Manufacturer” warrants to the original
purchaser of its products that such products are free from
manufacturing defect and does not warrant or guarantee the
workmanship performed by any person or firm installing its
products. The manufacturer’s obligation under this warranty
is limited solely to the original purchaser and solely shall be
limited to the replacement of the product sold. This warranty
will not extend to any product which has been modified in any
way or which has not been used in accordance with the printed
instructions. The manufacturer makes no other warranties
either expressed or implied. The end user must determine the
suitability of the product for their intended use.
ALWAYS DO A TEST FIRST.
Aqua-Seal Gold+™
Premium Natural Look Sealer
Aqua-Seal STC Technical Support
Phone+61 2 9521 4000or Email
Sealers
Natural Look
Stone, Tile & Concrete Solutions
Stone, Tile & Concrete Solutions